{"{0} = {1} ÷ {2}, then divide both by their greatest common divisor.":"{0} = {1} ÷ {2}，然后将两者都除以它们的最大公约数。","Absolute error":"绝对误差","Check: {0}":"检查：{0}","Decimal":"小数","Decimal to fraction converter":"小数转分数转换器","Engineering notation":"工程计数法","Enter a decimal, such as 0.625, 2.75, or 0.(3).":"输入小数，例如0.625、2.75或0.(3)。","Enter a number, such as 0.0450 or 1200.":"输入数字，例如0.0450或1200。","Enter a number, such as 45600, 0.00012, or 6.02e23.":"输入数字，例如45600、0.00012或6.02e23。","Enter both values.":"输入两个值。","Exact.":"精确。","Exactly {0}/{1}; rounded to the nearest 1/{2}.":"精确值为{0}/{1}；四舍五入到最近的1/{2}。","Exactly {0}/{1}; the nearest fraction with a denominator up to {2} is shown.":"精确值为{0}/{1}；显示分母不超过{2}的最接近分数。","exponent a multiple of 3":"指数为3的倍数","For a repeating decimal, put the repeating digits in brackets: 0.(3) for 0.333…, 0.1(6) for 0.1666….":"对于循环小数，请将循环数字放在括号中：0.333…写作0.(3)，0.1666…写作0.1(6)。","Largest denominator (optional)":"最大分母（可选）","Measured (experimental) value":"测量值（实验值）","Nearest 1/{0}":"最近的1/{0}","No: exact":"否：精确","Non-zero digits always count; zeros between them count; leading zeros never count; trailing zeros count only after a decimal point.":"非零数字始终计入有效数字；非零数字之间的零计入；前导零不计入；小数点后的末尾零才计入。","Number":"数字","Number, in standard form or as 4.56e-4":"数字，使用标准形式或写作4.56e-4","Percent error":"百分比误差","Percent error calculator":"百分比误差计算器","Round to":"四舍五入到","Round to a ruler mark":"四舍五入到刻度线","Rounded to {0} significant figures":"四舍五入到{0}位有效数字","Scientific notation":"科学计数法","Scientific notation converter":"科学计数法转换器","Scientific notation writes a number as a × 10ⁿ with 1 ≤ |a| < 10. Engineering notation keeps n a multiple of 3, matching the prefixes kilo, mega, milli, and micro.":"科学计数法将数字写成a × 10ⁿ，其中1 ≤ |a| < 10。工程计数法则使n保持为3的倍数，对应kilo、mega、milli和micro前缀。","Signed error":"带符号误差","Significant figures":"有效数字","Significant figures calculator":"有效数字计算器","Standard form":"标准形式","The measurement is too high.":"测量值过高。","The measurement is too low.":"测量值过低。","The true value cannot be 0: percent error divides by it.":"真实值不能为0：百分比误差需要用它作除数。","Trailing zeros in a whole number are ambiguous: write {0} or use scientific notation to show they count.":"整数末尾的零含义不明确：请写作{0}，或使用科学计数法表示这些零应计入有效数字。","True (accepted) value":"真实值（认可值）"}