{"3-digit code: two digits and a multiplier":"三位代码：两位数字和一个乘数","4-digit code: three digits and a multiplier":"四位代码：三位数字和一个乘数","A three-digit code is two digits and a multiplier in picofarads: 104 is 10 followed by four zeros, 100,000 pF or 100 nF. A third digit of 8 or 9 divides by 100 or 10, and R marks a decimal point, as in 4R7 = 4.7 pF. A letter after the code is the tolerance:":"三位代码由两位数字和一个以皮法为单位的乘数组成：104表示10后面跟四个零，即100,000 pF或100 nF。第三位数字为8或9时，分别除以100或10；R表示小数点，例如4R7=4.7 pF。代码后的字母表示容差：","Actual current":"实际电流","Calculated: {0}":"计算结果：{0}","Capacitance":"电容","Capacitance ({0})":"电容（{0}）","Capacitor code converter":"电容代码转换器","Circuit diagram":"电路图","Code":"代码","Code printed on the capacitor":"电容上印刷的代码","Code printed on the resistor":"电阻上印刷的代码","Code to value":"代码转数值","Current through the divider":"分压器中的电流","Custom":"自定义","Direction":"方向","E12 (10%)":"E12（10%）","E24 (5%)":"E24（5%）","EIA-96: a code for an E96 value and a letter multiplier":"EIA-96：E96数值代码和字母乘数","Enter a capacitance.":"请输入电容。","Enter a code such as 104, 473J, 229, or 4R7.":"请输入代码，例如104、473J、229或4R7。","Enter a marking such as 472, 1002, 4R7, or 01C.":"请输入标记，例如472、1002、4R7或01C。","Enter positive values in every field.":"请在每个字段中输入正数。","Enter the supply voltage, forward voltage, and current.":"请输入电源电压、正向电压和电流。","Green (older, yellowish)":"绿色（较旧，偏黄色）","Green, blue, or white":"绿色、蓝色或白色","In nanofarads and microfarads":"以纳法和微法表示","In picofarads":"以皮法表示","Infrared":"红外线","Input voltage (V)":"输入电压（V）","LED colour":"LED颜色","LED current (mA)":"LED电流（mA）","LED forward voltage (V)":"LED正向电压（V）","LED resistor calculator":"LED电阻计算器","LEDs in series":"串联LED数量","Marking type":"标记类型","No standard code":"无标准代码","Output voltage (V)":"输出电压（V）","Over 2.5 W: use a constant-current driver instead":"超过2.5 W：请改用恒流驱动器","Power in the resistor":"电阻功率","R = (supply voltage − forward voltage × number of LEDs) ÷ current. The resistor is rounded up to the next standard value, so the LED gets a little less than the target current rather than more. Forward voltages vary by LED; check the datasheet, and for several LEDs in parallel give each its own resistor.":"R=（电源电压−正向电压×LED数量）÷电流。电阻值会向上取整到下一个标准值，因此LED获得的电流会略低于目标值，而不会更高。不同LED的正向电压各不相同，请查阅数据表；多个LED并联时，应为每个LED分别配备一个电阻。","R marks the decimal point":"R表示小数点","R1, top (Ω)":"R1，上方（Ω）","R2, bottom (Ω)":"R2，下方（Ω）","Ratio":"比率","Red":"红色","Resistance":"电阻","Resistor to use":"应使用的电阻","SMD resistor code calculator":"SMD电阻代码计算器","Standard values":"标准值","Supply voltage (V)":"电源电压（V）","The output voltage must be above zero and below the input voltage.":"输出电压必须大于零且低于输入电压。","The supply voltage must be higher than the LEDs' total forward voltage ({0} V); add supply voltage or use fewer LEDs in series.":"电源电压必须高于LED的总正向电压（{0} V）；请提高电源电压或减少串联LED的数量。","Three digits are two significant digits and a power of ten (472 = 47 × 100 = 4.7 kΩ); four digits, used on 1% parts, are three digits and a power of ten (1002 = 10 kΩ). EIA-96 markings on small 1% parts use a two-digit index into the E96 series and a letter: Z × 0.001, Y or R × 0.01, X or S × 0.1, A × 1, B or H × 10, C × 100, D × 1 000, E × 10 000, F × 100 000. An underlined or barred code may mark a different scheme; check the maker's datasheet.":"三位代码由两个有效数字和一个十的幂组成（472=47×100=4.7 kΩ）；用于1%元件的四位代码由三个数字和一个十的幂组成（1002=10 kΩ）。小型1%元件上的EIA-96标记使用E96系列的两位索引和一个字母：Z×0.001，Y或R×0.01，X或S×0.1，A×1，B或H×10，C×100，D×1 000，E×10 000，F×100 000。带下划线或横线的代码可能表示另一种规则；请查阅制造商的数据表。","Three-digit codes hold two significant digits, such as 4.7 or 22":"三位代码包含两个有效数字，例如4.7或22","Tolerance":"容差","Unit":"单位","Use a {0} W resistor or larger":"请使用{0} W或更大功率的电阻","Value to code":"数值转代码","Voltage divider calculator":"分压器计算器","Vout = Vin × R2 ÷ (R1 + R2), with nothing connected to the output. A load across R2 draws current and pulls the output down, so keep the load's resistance at least ten times R2, or use a regulator to power anything that needs current.":"Vout=Vin×R2÷（R1+R2），且输出端未连接任何设备。连接在R2两端的负载会产生电流并拉低输出电压，因此负载电阻应至少为R2的十倍；或者使用稳压器为需要电流的设备供电。","Work out":"计算","Yellow or orange":"黄色或橙色","Zero-ohm jumper":"零欧姆跳线"}