{"3-digit code: two digits and a multiplier":"3位數代碼：兩個數字和一個倍率","4-digit code: three digits and a multiplier":"4位數代碼：三個數字和一個倍率","A three-digit code is two digits and a multiplier in picofarads: 104 is 10 followed by four zeros, 100,000 pF or 100 nF. A third digit of 8 or 9 divides by 100 or 10, and R marks a decimal point, as in 4R7 = 4.7 pF. A letter after the code is the tolerance:":"三位數代碼由兩個數字和以pF為單位的倍率組成：104就是10後面加上四個零，也就是100,000 pF或100 nF。第三位數字為8或9時，分別除以100或10；R代表小數點，例如4R7 = 4.7 pF。代碼後面的字母代表容差：","Actual current":"實際電流","Calculated: {0}":"計算結果：{0}","Capacitance":"電容量","Capacitance ({0})":"電容量（{0}）","Capacitor code converter":"電容器代碼轉換器","Circuit diagram":"電路圖","Code":"代碼","Code printed on the capacitor":"電容器上印刷的代碼","Code printed on the resistor":"電阻器上印刷的代碼","Code to value":"代碼轉數值","Current through the divider":"分壓器中的電流","Custom":"自訂","Direction":"方向","E12 (10%)":"E12 (10%)","E24 (5%)":"E24 (5%)","EIA-96: a code for an E96 value and a letter multiplier":"EIA-96：E96數值代碼和字母倍率","Enter a capacitance.":"請輸入電容量。","Enter a code such as 104, 473J, 229, or 4R7.":"請輸入代碼，例如104、473J、229或4R7。","Enter a marking such as 472, 1002, 4R7, or 01C.":"請輸入標示，例如472、1002、4R7或01C。","Enter positive values in every field.":"請在每個欄位輸入正值。","Enter the supply voltage, forward voltage, and current.":"請輸入供應電壓、順向電壓和電流。","Green (older, yellowish)":"綠色（較舊、偏黃色）","Green, blue, or white":"綠色、藍色或白色","In nanofarads and microfarads":"以nF和μF表示","In picofarads":"以pF表示","Infrared":"紅外線","Input voltage (V)":"輸入電壓（V）","LED colour":"LED顏色","LED current (mA)":"LED電流（mA）","LED forward voltage (V)":"LED順向電壓（V）","LED resistor calculator":"LED電阻器計算機","LEDs in series":"串聯LED數量","Marking type":"標示類型","No standard code":"沒有標準代碼","Output voltage (V)":"輸出電壓（V）","Over 2.5 W: use a constant-current driver instead":"超過2.5 W：請改用定電流驅動器","Power in the resistor":"電阻器功率","R = (supply voltage − forward voltage × number of LEDs) ÷ current. The resistor is rounded up to the next standard value, so the LED gets a little less than the target current rather than more. Forward voltages vary by LED; check the datasheet, and for several LEDs in parallel give each its own resistor.":"R =（供應電壓 − 順向電壓 × LED數量）÷ 電流。電阻器會向上取至下一個標準值，因此LED取得的電流會略低於目標值，而不是超過目標值。不同LED的順向電壓各不相同，請查閱資料表；如果有多個LED並聯，請為每個LED各自使用一個電阻器。","R marks the decimal point":"R代表小數點","R1, top (Ω)":"R1，上方（Ω）","R2, bottom (Ω)":"R2，下方（Ω）","Ratio":"比例","Red":"紅色","Resistance":"電阻值","Resistor to use":"所需電阻器","SMD resistor code calculator":"SMD電阻器代碼計算機","Standard values":"標準值","Supply voltage (V)":"供應電壓（V）","The output voltage must be above zero and below the input voltage.":"輸出電壓必須大於0且低於輸入電壓。","The supply voltage must be higher than the LEDs' total forward voltage ({0} V); add supply voltage or use fewer LEDs in series.":"供應電壓必須高於LED的總順向電壓（{0} V）；請提高供應電壓，或減少串聯的LED數量。","Three digits are two significant digits and a power of ten (472 = 47 × 100 = 4.7 kΩ); four digits, used on 1% parts, are three digits and a power of ten (1002 = 10 kΩ). EIA-96 markings on small 1% parts use a two-digit index into the E96 series and a letter: Z × 0.001, Y or R × 0.01, X or S × 0.1, A × 1, B or H × 10, C × 100, D × 1 000, E × 10 000, F × 100 000. An underlined or barred code may mark a different scheme; check the maker's datasheet.":"三位數代碼由兩個有效數字和10的次方組成（472 = 47 × 100 = 4.7 kΩ）；用於1%元件的四位數代碼由三個數字和10的次方組成（1002 = 10 kΩ）。小型1%元件上的EIA-96標示，會使用E96系列的兩位數索引和一個字母：Z × 0.001、Y或R × 0.01、X或S × 0.1、A × 1、B或H × 10、C × 100、D × 1 000、E × 10 000、F × 100 000。加底線或刪除線的代碼可能代表不同的標示方式；請查閱製造商的資料表。","Three-digit codes hold two significant digits, such as 4.7 or 22":"三位數代碼包含兩個有效數字，例如4.7或22","Tolerance":"容差","Unit":"單位","Use a {0} W resistor or larger":"請使用{0} W或更大的電阻器","Value to code":"數值轉代碼","Voltage divider calculator":"分壓器計算機","Vout = Vin × R2 ÷ (R1 + R2), with nothing connected to the output. A load across R2 draws current and pulls the output down, so keep the load's resistance at least ten times R2, or use a regulator to power anything that needs current.":"Vout = Vin × R2 ÷（R1 + R2），且輸出端未連接任何裝置。跨接在R2兩端的負載會汲取電流並拉低輸出電壓，因此請讓負載電阻至少是R2的十倍，或使用穩壓器為任何需要電流的裝置供電。","Work out":"計算","Yellow or orange":"黃色或橘色","Zero-ohm jumper":"零歐姆跳線"}